top of page
PRODUCTS
Film Blowing Machine
Film Blowing Machine
The Film Blowing Machiner is an automatic machine that transforms plastic grains into virgin or recycled plastic spools, which are later used to produce bags, garbage bags, ice bags, sand bags and plastic bags into general.
To produce the coils, the Film Blowing Machine uses a 50 mm thread, and produces high and low density, linear polyethylene film.
Film Blowing Machine - Technical Descriptions:
Technical Information of Film Blowing Machine - 50mm
Reducer Model: 146
Production: up to 60 kg/h.
Winder width: 900 mm (with pneumatic closing)
Machine Dimension: 4.5m high x 2m wide x 4.5m long (including winder)
Film Blowing Machine, with 50mm thread diameter, L/D 30:1, Model: 50/800, pulling power 2kw, motor 15kw, 380v, 50-60hz,
The Film Blowing Machine uses a gearbox with high torque, low noise, high hardness and internal lubrication, and has:
Swap Mobile Screen.
Swivel head and double cooling ring.
3CV fan to inflate the balloon.
Winder with closing through pneumatic cylinders.
Pull rollers with closing through pneumatic cylinders.
Pinch rollers with additional knurled cylinder for calendering the film.
20CV screw main motor with frequency inverter.
Other motors also have frequency inverters.
Panel with 5 heating zones.
Two Fan for thread ventilation.
Head with two dies, one with 180mm die and the other with 80mm.
Air Ring for LDPE and HDPE
original machine accordion
The Film Blowing Machiner is an automatic machine that transforms plastic grains into virgin or recycled plastic spools, which are later used to produce bags, garbage bags, ice bags, sand bags and plastic bags into general.
To produce the coils, the Film Blowing Machine uses a 50 mm thread, and produces high and low density, linear polyethylene film.
Film Blowing Machine - Technical Descriptions:
Technical Information of Film Blowing Machine - 50mm
Reducer Model: 146
Production: up to 60 kg/h.
Winder width: 900 mm (with pneumatic closing)
Machine Dimension: 4.5m high x 2m wide x 4.5m long (including winder)
Film Blowing Machine, with 50mm thread diameter, L/D 30:1, Model: 50/800, pulling power 2kw, motor 15kw, 380v, 50-60hz,
The Film Blowing Machine uses a gearbox with high torque, low noise, high hardness and internal lubrication, and has:
Swap Mobile Screen.
Swivel head and double cooling ring.
3CV fan to inflate the balloon.
Winder with closing through pneumatic cylinders.
Pull rollers with closing through pneumatic cylinders.
Pinch rollers with additional knurled cylinder for calendering the film.
20CV screw main motor with frequency inverter.
Other motors also have frequency inverters.
Panel with 5 heating zones.
Two Fan for thread ventilation.
Head with two dies, one with 180mm die and the other with 80mm.
Air Ring for LDPE and HDPE
original machine accordion
SOS 05 Machine for Paper Bags with Square Bottom - Reel Feed - Small Bags
Three-phase machine at 380v, 60hz, which has a motor and frequency inverter, in addition to an expansive axis, voltage controller, aligner, water-based glue system and automatic counter. All lengths are controlled by PLC and HMI Touch Screen, in addition to servo motor and driver. Photocell used to work with printed material
Technical Parameters:
Paper Thickness: 60 to 160 gsm
Tube cutting length: 270 to 530 mm
Bag length: 225 to 470 mm
Bag width: 120 to 280 mm
Bag Bottom Width: 60 to 150 mm
Bag bottom accordion: 30 to 75 mm (each accordion)
Power Consumption: 12kw
Production Capacity: 180 pcs/minute
Machine weight: 7000 kg
Coil Width: 380 to 950 mm
Max bobbin weight: 800kg
Max coil diameter: 1200mm
Paper core diameter: 76mm
General Dimensions: 10500 x 3600 x 1900 mm
Technical Parameters:
Paper Thickness: 60 to 160 gsm
Tube cutting length: 270 to 530 mm
Bag length: 225 to 470 mm
Bag width: 120 to 280 mm
Bag Bottom Width: 60 to 150 mm
Bag bottom accordion: 30 to 75 mm (each accordion)
Power Consumption: 12kw
Production Capacity: 180 pcs/minute
Machine weight: 7000 kg
Coil Width: 380 to 950 mm
Max bobbin weight: 800kg
Max coil diameter: 1200mm
Paper core diameter: 76mm
General Dimensions: 10500 x 3600 x 1900 mm
Extruder Mill for EPS Styrofoam - Sludge
- Production: up to 200kgs/hour
- Model: 150
- Main Engine: 15kw
- Resistances: 2 kW
- Feeding Mouth: 600*800 mm
- Temperature up to: 200º C
- Power: 380v, 60hz, three-phase
- Dimensions: 1400mm x 1350mm x 1500m
- Weight: 325 kg
- Model: 150
- Main Engine: 15kw
- Resistances: 2 kW
- Feeding Mouth: 600*800 mm
- Temperature up to: 200º C
- Power: 380v, 60hz, three-phase
- Dimensions: 1400mm x 1350mm x 1500m
- Weight: 325 kg
Stamping Printer
stamper
The Stamping Printer is an industrial and versatile machine for printing on plastic bags and bags, paper, raffia and cardboard materials, such as pizza boxes. BRASIA supplies Stampers of 2, 3 and 4 Colors in models: 850 and 1050.
The Stamper also has optional items, such as the Fan to optimize the drying process, the Pneumatic Ink Pump to keep the ink watery for longer while reducing the risk of accidents, the Air Compressor and the Bags to prevent material from being inserted into the machine the wrong way.
Stamper - Technical Descriptions:
Stamper Technical Information
Electronic Panel for Production;
Optomagnetic Orientation Control;
Air Control;
Frequency Inverter for Speed Control;
Counting Printed Bags;
Anilox roll with 200 lines;
Robust Sheet Steel Machine Structure:
Maximum Material Input Width:
680 or 880 mm
Cylinder Diameter: 1300 mm
Maximum Print Length: 1200 mm
Maximum Print Width: 600 or 700 mm
Rubber Thickness for Printing (Padrate): 2.8-6 mm
Thicknesses for Plastic Bags: 6 - 50 microns.
Printing Speed: 200-2400 pieces/hour
Machine Width: 1400mm
Machine Length: 1400mm
Machine height: 1200mm
Greenhouse: Length 2200mm
Width: 900mm
Total weight, Oven + Machine: 800kg
Optional: Drying oven and paint pump.
The Stamping Printer is an industrial and versatile machine for printing on plastic bags and bags, paper, raffia and cardboard materials, such as pizza boxes. BRASIA supplies Stampers of 2, 3 and 4 Colors in models: 850 and 1050.
The Stamper also has optional items, such as the Fan to optimize the drying process, the Pneumatic Ink Pump to keep the ink watery for longer while reducing the risk of accidents, the Air Compressor and the Bags to prevent material from being inserted into the machine the wrong way.
Stamper - Technical Descriptions:
Stamper Technical Information
Electronic Panel for Production;
Optomagnetic Orientation Control;
Air Control;
Frequency Inverter for Speed Control;
Counting Printed Bags;
Anilox roll with 200 lines;
Robust Sheet Steel Machine Structure:
Maximum Material Input Width:
680 or 880 mm
Cylinder Diameter: 1300 mm
Maximum Print Length: 1200 mm
Maximum Print Width: 600 or 700 mm
Rubber Thickness for Printing (Padrate): 2.8-6 mm
Thicknesses for Plastic Bags: 6 - 50 microns.
Printing Speed: 200-2400 pieces/hour
Machine Width: 1400mm
Machine Length: 1400mm
Machine height: 1200mm
Greenhouse: Length 2200mm
Width: 900mm
Total weight, Oven + Machine: 800kg
Optional: Drying oven and paint pump.
Plastic Bag Making Machine - Automatic
-Production Speed:
-Model 1 of 150 - 200 bags per minute
-Model 2 of 250 - 300 bags per minute
-Maximum width: 400 mm x 2
-Maximum Length: 650 mm
-Input Coil Diameter: 700 mm
-Bag Thickness: 0.015 - 0.035 mm
-Air Pressure: 5 kg/CM2
-Total Power: 13 HP
-Machine Weight: 1600 kg
-Dimensions: 6000 x 1400 x 1600 mm (length x width x height)
-Model 1 of 150 - 200 bags per minute
-Model 2 of 250 - 300 bags per minute
-Maximum width: 400 mm x 2
-Maximum Length: 650 mm
-Input Coil Diameter: 700 mm
-Bag Thickness: 0.015 - 0.035 mm
-Air Pressure: 5 kg/CM2
-Total Power: 13 HP
-Machine Weight: 1600 kg
-Dimensions: 6000 x 1400 x 1600 mm (length x width x height)
Cut and Weld Bottom and Side 900
The 900 Deep and Side Cut and Weld Machine is ideal for garbage bags and other thick plastic bags that require strong welding. This cutting machine is made up of the following options already included: Photocell, pneumatic punch, accordion, side film opener and adhesive tape applicator.
Cutting and Welding Bottom and Side 900 - Technical Descriptions:
This automatic cutting and welding machine has a servo motor and driver, PLC, touch screen HMI, anti-static set composed of transformer and bar, temperature controller, stop alarm, automatic counter, frequency inverter, dual axis power supply, deep weld, cutting knife, conductive belt and simple table.
Production: 25-200 pcs/min
Max Width: 800mm
Max Length: 85-2500mm
Thickness: 0.02 - 0.40 mm
Power: 3kw
Dimensions: 4200 x 1800 x 1700 mm
Cutting and Welding Bottom and Side 900 - Technical Descriptions:
This automatic cutting and welding machine has a servo motor and driver, PLC, touch screen HMI, anti-static set composed of transformer and bar, temperature controller, stop alarm, automatic counter, frequency inverter, dual axis power supply, deep weld, cutting knife, conductive belt and simple table.
Production: 25-200 pcs/min
Max Width: 800mm
Max Length: 85-2500mm
Thickness: 0.02 - 0.40 mm
Power: 3kw
Dimensions: 4200 x 1800 x 1700 mm
Small Size Cutter
The Small Size Cutter is an automatic machine for cutting coils into sheets/reams of various materials. Our models have counting and automatic stop for production control.
Great machine for those looking for precision in cutting.
Technical Descriptions Small Size Cutter:
-Sheet Cut: 20-180 sheets per minute
- Materials: PVC, PE, PP, BOPP, Paper and others
-Maximum Cut Length: 20 - 1000 mm
-Maximum cutting width: 790 mm
-Accuracy: +- 0.2 mm
- Material Thickness: 35 - 150 grams
- Coil diameter: up to 900 mm
- Machine Weight: 1000 Kg
- General Dimensions: 3150 x 1400 x 1400 mm
Great machine for those looking for precision in cutting.
Technical Descriptions Small Size Cutter:
-Sheet Cut: 20-180 sheets per minute
- Materials: PVC, PE, PP, BOPP, Paper and others
-Maximum Cut Length: 20 - 1000 mm
-Maximum cutting width: 790 mm
-Accuracy: +- 0.2 mm
- Material Thickness: 35 - 150 grams
- Coil diameter: up to 900 mm
- Machine Weight: 1000 Kg
- General Dimensions: 3150 x 1400 x 1400 mm
Ink pump
The Ink Pump works through pneumatic power, that is, it uses compressed air as a source of energy, which does not heat up or generate sparks, which guarantees the ink pump a perfect functioning even in highly flammable environments.
This accessory can be used in any type of flexographic printer and stamping machine, both in machines that use solvent and water-based ink. This model of ink pump has been gaining ground in the market, as it works better than electric pumps, which generate sparks, increasing the chances of causing short circuits and fires, in addition to generating high costs due to high energy consumption and maintenance needs.
The Pneumatic Ink Pump is economical, versatile, efficient, safe and corrosion resistant.
Ink Pump - Technical Descriptions:
The Ink Pump has an aluminum pneumatic agitator with 2 registers, pumping control and ink recirculation. In addition, it also has an adjustable angler according to the level of paint, bucket (inkwell) in stainless steel with a capacity of 18L, maximum flow of 10L/min and works with pressure of up to 6 bar.
This accessory can be used in any type of flexographic printer and stamping machine, both in machines that use solvent and water-based ink. This model of ink pump has been gaining ground in the market, as it works better than electric pumps, which generate sparks, increasing the chances of causing short circuits and fires, in addition to generating high costs due to high energy consumption and maintenance needs.
The Pneumatic Ink Pump is economical, versatile, efficient, safe and corrosion resistant.
Ink Pump - Technical Descriptions:
The Ink Pump has an aluminum pneumatic agitator with 2 registers, pumping control and ink recirculation. In addition, it also has an adjustable angler according to the level of paint, bucket (inkwell) in stainless steel with a capacity of 18L, maximum flow of 10L/min and works with pressure of up to 6 bar.
Flow Pack Packaging Machine - Standard
Production Speed: 40 - 230 packs per minute
Maximum Film Width: Up to 250mm
Packing Length: 30 - 150 mm
Pack width: 30 - 110 mm
Maximum Pack Height: 40 mm
Coil Roll Diameter: up to 320 mm
Sealing: 3 sides
Includes:
Frequency inverter
Temperature control
Touch Screen HMI
Options:
Photocell
Print Dater
Maximum Film Width: Up to 250mm
Packing Length: 30 - 150 mm
Pack width: 30 - 110 mm
Maximum Pack Height: 40 mm
Coil Roll Diameter: up to 320 mm
Sealing: 3 sides
Includes:
Frequency inverter
Temperature control
Touch Screen HMI
Options:
Photocell
Print Dater
Filling Machine for Grains, Snacks and Powder
The Filling Machine for Grains, Snacks and Powder is a machine for volumetric filling of grains, snacks and powder in sachets. It is fed by a coil, which forms the sachet used to automatically fill the product.
- Production Speed: Max. 60 packs per min (depends on length)
- Model: 200
- Air Consumption: 2.5 m3/min 6kg/cm2
- Volume: 300g min - 2.5kg max
- Film Width: 370 mm
- Packing width: 50-180 mm
- Packing Length: 80-240 mm
- Film Thickness: 0.04 to 0.08 millimeters
- Electric Power: 220V, 50/60Hz. 2.4kw
- Machine weight: 350 kg
- Production Speed: Max. 60 packs per min (depends on length)
- Model: 200
- Air Consumption: 2.5 m3/min 6kg/cm2
- Volume: 300g min - 2.5kg max
- Film Width: 370 mm
- Packing width: 50-180 mm
- Packing Length: 80-240 mm
- Film Thickness: 0.04 to 0.08 millimeters
- Electric Power: 220V, 50/60Hz. 2.4kw
- Machine weight: 350 kg
Non Woven Bags and Sacks Machine - Non Woven
-Production Speed: up to 100 pieces/min
-Model: 800
-Useful Width of Material Input: 1450 mm
- Bag height: 200 - 680 mm
- Bag width: 100 - 800 mm
- Bag accordion: 180 mm
- Material Thickness: 30 - 100 gsm
-Machine Power: 13 kW
- Machine Weight: 2400 kg
- Machine Dimensions: 7600x2100x2000 mm
-Model: 800
-Useful Width of Material Input: 1450 mm
- Bag height: 200 - 680 mm
- Bag width: 100 - 800 mm
- Bag accordion: 180 mm
- Material Thickness: 30 - 100 gsm
-Machine Power: 13 kW
- Machine Weight: 2400 kg
- Machine Dimensions: 7600x2100x2000 mm
Surgical Mask Machine for Non-Woven Fabrics (TNT) with Strap Application - Automatic
Mask Size: 17.5 x 9.5 cm (customer can change)
Production speed: up to 60 pieces per minute
Power: 8 kW
Machine weight: 1630 kg
Machine dimensions: 4500x3000x1800 mm
* Automatic machine in stainless steel and chrome steel, rubberized rollers, voltage controller, sensors, aligner, photocell, servo motor and driver, frequency inverter, PLC and HMI (touch screen); anti-static set consisting of transformer and busbar; ultrasound set consisting of generator, sonotrode, mold and fans; cutting knife and exit mat.
Production speed: up to 60 pieces per minute
Power: 8 kW
Machine weight: 1630 kg
Machine dimensions: 4500x3000x1800 mm
* Automatic machine in stainless steel and chrome steel, rubberized rollers, voltage controller, sensors, aligner, photocell, servo motor and driver, frequency inverter, PLC and HMI (touch screen); anti-static set consisting of transformer and busbar; ultrasound set consisting of generator, sonotrode, mold and fans; cutting knife and exit mat.
Machine for Propé TNT (Non Woven Fabric)
Machine Dimensions: 3600 x 1030 x 1500 mm
Production Capacity: up to 100 pieces/min
Machine weight: 420 kg
Power: 220V / 3.5kW
Product Depth: 13 to 20 cm
Product Length: 34 to 50 cm
Production Capacity: up to 100 pieces/min
Machine weight: 420 kg
Power: 220V / 3.5kW
Product Depth: 13 to 20 cm
Product Length: 34 to 50 cm
Cap Machine - Non Woven and Plastic
The Cap Machine is a disposable cap making machine from Non Woven and Plastic, which are supplied to hospitals, clinics, kitchens, hotels, in addition to PPE (Personal Protective Equipment). It is a versatile machine with excellent value for money. Constructed in stainless steel.
-Production Capacity: up to 130 pieces per minute
- Coil Width: 480 mm
- Coil diameter: up to 600 mm
- Non Woven thickness: 12-20 gsm
- Plastic Thickness: 15 - 20 microns
-Cap Size: 430 x 200 mm (according to customer specification)
-Voltage: 220v 60hz
-Power: 9 kW
- Machine Weight: 800 kg
- Machine Dimensions: 3800 x 800 x 1000 mm
- Machine with automatic mechanisms, from the feeding of raw materials to the finished product;
- Constructed in Stainless Steel;
- Voltage Control;
- Production Speed Control;
- Heat set consisting of resistors, counters and temperature indicators;
- Transport belts;
- Control Panel;
- Command button;
- Ultrasound Set for Reinforced Welding;
- Frequency inverter.
-Production Capacity: up to 130 pieces per minute
- Coil Width: 480 mm
- Coil diameter: up to 600 mm
- Non Woven thickness: 12-20 gsm
- Plastic Thickness: 15 - 20 microns
-Cap Size: 430 x 200 mm (according to customer specification)
-Voltage: 220v 60hz
-Power: 9 kW
- Machine Weight: 800 kg
- Machine Dimensions: 3800 x 800 x 1000 mm
- Machine with automatic mechanisms, from the feeding of raw materials to the finished product;
- Constructed in Stainless Steel;
- Voltage Control;
- Production Speed Control;
- Heat set consisting of resistors, counters and temperature indicators;
- Transport belts;
- Control Panel;
- Command button;
- Ultrasound Set for Reinforced Welding;
- Frequency inverter.
Automatic Chip Trimmer
The Automatic Chip Trimmer is an equipment used in film extruders. The extruders can be balloon or flat with a flat die head. With the use of the trimmer, 100% of the raw material is used, whether recycled virgin or additives. The equipment allows the industry not to waste anything.
The Automatic Chip Trimmer is composed of pulleys to transport the trim, mill with motor, suction hose and funnel with motorized forced feeder. The system is directly connected to the extruder hopper.
The Automatic Chip Trimmer has a power of 4kw and a speed of 5-10kgs/hour. The voltage is 380v and 60hz. It can be controlled by frequency inverter. The maximum trim width is 160mm.
The Automatic Chip Trimmer is composed of pulleys to transport the trim, mill with motor, suction hose and funnel with motorized forced feeder. The system is directly connected to the extruder hopper.
The Automatic Chip Trimmer has a power of 4kw and a speed of 5-10kgs/hour. The voltage is 380v and 60hz. It can be controlled by frequency inverter. The maximum trim width is 160mm.
Winder
1300 mm wide winder
With a razor or stylus system, with special articulated support, for cutting flexible materials such as BOPP, PP, PE, PVC and others, as well as plain printed matter.
Also with a cutting system with rotating knives for cutting rigid and semi-rigid materials, for example: paperboard, cardboard, embossed paper, felt, all types of laminates and sandwiches.
Coil input 1300 mm wide and diameter up to 860 mm, with aligner, expanding shaft, and electromagnetic voltage control.
Outputs with dual articulated and expansive shafts, with individual electromagnetic control.
Electronic photocell, for reading longitudinal printing.
Meter meter through electronic sensor.
Automatic stop sensor when it completes the programmed footage.
Speed control through digital programming
All operational functions are programmed through a digital panel and with memory of the programmed functions.
With a razor or stylus system, with special articulated support, for cutting flexible materials such as BOPP, PP, PE, PVC and others, as well as plain printed matter.
Also with a cutting system with rotating knives for cutting rigid and semi-rigid materials, for example: paperboard, cardboard, embossed paper, felt, all types of laminates and sandwiches.
Coil input 1300 mm wide and diameter up to 860 mm, with aligner, expanding shaft, and electromagnetic voltage control.
Outputs with dual articulated and expansive shafts, with individual electromagnetic control.
Electronic photocell, for reading longitudinal printing.
Meter meter through electronic sensor.
Automatic stop sensor when it completes the programmed footage.
Speed control through digital programming
All operational functions are programmed through a digital panel and with memory of the programmed functions.
Want to know more? Contact.
We are here to help you. Get in touch by phone, email or social media.
bottom of page